Why Your EDDM Carrier Routes Never Match Your Farm Boundaries
EDDM prices by the route, not by the rooftop. That single fact explains almost every frustration agents run into after their first order. The flat per-piece rate looks great on paper. Then the map comes back and half your farm sits in one route while the other half spills into three more, two of which barely touch your actual target streets.
This isn't a flaw in EDDM. It's how the US Postal Service built the program, and once you understand the logic behind it, you can work with it instead of fighting it.
How USPS Carrier Routes Actually Work
A carrier route is the path one mail carrier walks or drives in a day, not a neighborhood boundary someone drew with real estate in mind. Routes get redrawn periodically as delivery volume shifts, which means a route map that worked for a campaign last year can look different today.
Each route also carries a published household count and a residential delivery count, and EDDM requires you to mail to every address on a route you select. You can't skip the back half of a cul-de-sac because it falls outside your farm. It's all or nothing per route.
In dense Orange County, Los Angeles, and San Diego zip codes, this usually means routes are small and numerous, so stitching together a tight farm takes more routes, not fewer. In lower-density pockets, the opposite problem shows up: one route can stretch well past where your farm actually ends.
Where the Mismatch Shows Up Most
A few patterns come up again and again when agents pull their first route map for a new farm:
A busy street splits a route in half. One side of Main Street is in Route A, the other side is in Route B, and your farm was built around "everyone on Main Street."
Condo and apartment buildings skew the count. A single route can include a 200-unit complex that inflates your piece count and your bill, even though you only wanted the single-family homes nearby.
Commercial addresses ride along for free. EDDM includes business addresses on a selected route, which can be useful for a listing push to local businesses, or just dead weight you're paying to mail.
Your farm straddles a route boundary. The two streets that matter most to you sit on opposite sides of the line, so no single EDDM selection captures both without adding routes you don't need.
None of these mean EDDM was the wrong call. They mean the map needs a second look before you lock in a route selection, not after the postcards are already at the post office.
Three Ways to Handle the Mismatch
Once you've pulled the route map for your farm, you generally have three options, and most agents end up combining two of them over time.
Round up and accept some overmail. Select every route that touches your farm, even partially, and treat the extra addresses as low-cost exposure rather than waste. At EDDM's per-piece pricing, a modest amount of overmail is often cheaper than the alternative below.
Round down and accept some gaps. Drop routes that only clip the edge of your farm and live with a few missed streets. This keeps cost tight but leaves visible holes in your coverage, which matters more if you're trying to claim a neighborhood as "yours."
Layer in a targeted list for the gaps. Use EDDM for the routes that cleanly match your farm, then supply your own targeted mailing list for the specific streets EDDM leaves out. REMD doesn't source mailing lists, so this piece has to come from the agent's own data or a list provider, but it pairs well with an EDDM base.
There's no universally right answer here. A luxury farm where precision matters more than reach usually leans toward option two or three. A high-turnover starter-home farm where volume drives response usually leans toward option one.
When the Mismatch Means You Should Mix Methods
If your farm boundary follows anything other than a wide, obvious edge like a freeway or a park, expect at least some mismatch. Farms drawn around school district lines, HOA boundaries, or "everything west of the boulevard" almost never line up cleanly with carrier routes.
In that case, mixing EDDM with a smaller targeted mailing for the edge streets usually beats forcing the whole farm through EDDM alone. You get the lower per-piece cost where the routes fit, and precision where they don't.
This is also where agents in Orange County, Los Angeles, and San Diego tend to see the clearest case for mixing: dense city blocks with tight routes next to one or two outlier streets that belong to a different route entirely.

Making the Most of the Routes You Do Mail
Once the route selection is locked, the postcard itself still has to earn attention from everyone on that route, not just the ones who were already your ideal prospect. A route that includes some addresses outside your core farm is a reason to keep messaging broad enough to still land (market activity, recent sales, general neighborhood value) rather than hyper-specific copy that only makes sense to the handful of streets you really wanted.
A few things worth checking before you finalize any EDDM order:
Pull the current route map again if more than a few months have passed since your last order. Routes do get redrawn.
Compare the route's published count against what you expect your farm size to be. A big gap is a sign the route includes more than you think.
Decide before you order whether overmail, gaps, or a blended approach fits this specific farm, rather than defaulting to the same choice every time.
Bring us your artwork and we handle the rest, printed and mailed in-house at our Santa Ana facility, ordered and managed through our online ordering portal. If you're not sure which routes actually match your farm, that's a quick conversation before you place the order, not after.



